Winchester model 90 22 short octagon barrel value

It can be done in the home shop easily enough with a little care. They have no carrier in stock at present, but a complete one lists at $49.95. Numrich has replacement octagon barrels for $81.05 and many other parts available. If the desire was to reconvert to 22 short, the additional cost may be explained, but it is still way too high. Liners from Brownells are under $40.00 last time I purchased one, labor is a couple of hours tops. A competent gunsmith should do it for between $100 & $200, probably closer to the latter. The $500 figure for a simple reline is way too high. When taken down, the front of the receiver and barrel remain attached and must be separated to reline or rebarrel. The 19 are basically the same rifle, parts are commonly available and will interchange. Thanks for taking the time to slog through this terribly long post! My question, then, is this: is there a cheaper way to work this out? Or, specifically, is there anybody in the Boise, Idaho area who would be able to remove the barrel (without beating it up the way that I probably would) so that I can have a machinist work on it? Or maybe even a machinist who would like to do the work? So, after all that hand-wringing, I come to the end of my story. Unfortunately, this one is a work of love and, as much as I cherish my 40-some year old memories of shooting with my grandfather, I can't justify that much money on a rifle that, in the end, isn't going to be shot all that much anyway. And if this was a gun that I had as an investment, I'd pay the price and have it done, then recover it at the other end. Now, I don't begrudge the gunsmith the money at all - he's got to be paid for his work or else there's no food on the table. Unfortunately, that's expensive enough to force me to put the rifle up on the mantle and just look at it. He ran some numbers and came up with a total of $500 for parts and labor (about $140 in parts, the rest labor). I called up my local gunsmith to chat with him about relining the barrel. Not restored, mind you, but just so that I can send a round downrange and be confident that it will end up where I pointed it. So I really want to put this gun back into shooting condition. We shot this rifle and another 1906 that was my dad's when he was a kid. Now, this rifle has very special meaning to me because I only got to go shooting with my grandfather a couple of times before he died in 1969 when I was seven. And, as a bonus, it looks like the rifling, other than the last few inches at the muzzle, has seen much better days - as evidenced by keyholing at 50 feet.

The problem is that he didn't really clean the rifle as well as he should have and the effects of the corrosive ammo, along with the shorts in a long rifle chamber caused quite a bit of erosion, to the point that anything other than a short will not extract because the mouth expands too much. I know that it was done before Gramps got it because they wouldn't have been able to afford to rebarrel the rifle - things really were pretty tough for them.ДЄnyway, Gramps still shot shorts in the rifle and kept shooting them for the next 30 or 40 years.

But sometime around 1919 (roughly), the barrel was replaced with one that would chamber all three. Now, Gramps's rifle was made in 1906, back when the only round the rifle would chamber was. Gramps shot that rifle a lot - in fact, between it and my great grandfather's Colt Lightning rifle, they were able to eat through some lean times.

When my grandfather was a boy, back around 1920, his dad (my great grandfather) bought him a Winchester 1906 rifle. I ran into Carla over at the Winchester Collector's Forum and she suggested that I bring my sad tale over here, so here I am.

However, non-stock calibers are extra, base price starting at $50.00+. We can make most calibers and barrel weights (numbers). NOTE: The 1885 rifles were made in a lot of caliber bore sizes, ranging from. Stock Calibers: Original вЂ™44 Winchester Rim Fire or Center Fire 1866 Five Groove Rifling (also early 1873)

Winchester model 90 22 short octagon barrel value